help with accessport please
Thread Starter
Registered User
iTrader: (1)
Joined: Aug 2007
Posts: 600
From: Rohnert Park/Los Altos Hills, CA
Car Info: 04 AW WRX
help with accessport please
Just installed my downpipe and i go to tune it to stage 2 and it says error low voltage check cable what do i do please help me out somebody
Registered User
iTrader: (16)
Joined: Jan 2009
Posts: 490
From: Berkeley, CA
Car Info: '08 FXT - VF43'd
Probably try a different USB cable? Make sure the connection from the dongle to the OBDII port is secure as well.
Here is more info from the Cobb forums, but not sure if it helps. Probably best bet to just call Cobb, but they may be closed by now.
http://www.cobbforums.com/forums/sho...hp?67496-Uh-oh
Here is more info from the Cobb forums, but not sure if it helps. Probably best bet to just call Cobb, but they may be closed by now.
http://www.cobbforums.com/forums/sho...hp?67496-Uh-oh
Last edited by lickwid; Mar 25, 2010 at 06:14 PM.
iClub Silver Vendor
iTrader: (12)
Joined: Mar 2003
Posts: 8,228
From: 631 Railroad Ave. Fairfield, CA
Car Info: A Laptop
You're most likely missing the little white init plug. It should have come with your access port and you need to plug it into the harness under the dash whenever you reflash the ECU. Its basically a little terminal connector with 2 wires looped in it. If you do have this plugged in, then you need to check your battery voltage.
Thanks
-- Ed
Thanks
-- Ed
Friendly Neighborhood Ogre
iTrader: (6)
Joined: Mar 2000
Posts: 19,930
From: www.gunatics.com
Car Info: GUNATICS.COM
you're most likely missing the little white init plug. It should have come with your access port and you need to plug it into the harness under the dash whenever you reflash the ecu. Its basically a little terminal connector with 2 wires looped in it. If you do have this plugged in, then you need to check your battery voltage.
Thanks
-- ed
Thanks
-- ed
Thread Starter
Registered User
iTrader: (1)
Joined: Aug 2007
Posts: 600
From: Rohnert Park/Los Altos Hills, CA
Car Info: 04 AW WRX
You're most likely missing the little white init plug. It should have come with your access port and you need to plug it into the harness under the dash whenever you reflash the ECU. Its basically a little terminal connector with 2 wires looped in it. If you do have this plugged in, then you need to check your battery voltage.
Thanks
-- Ed
Thanks
-- Ed
iClub Silver Vendor
iTrader: (12)
Joined: Mar 2003
Posts: 8,228
From: 631 Railroad Ave. Fairfield, CA
Car Info: A Laptop
You can also just use a couple paper clips if you're feeling adventurous
.Thanks
-- Ed
Registered User
iTrader: (14)
Joined: May 2008
Posts: 1,581
From: Hayward, CA
Car Info: amber lamps/fire engine/06 STi
i got that when my car's battery was actually on low voltage and the entire map didnt get to flash all the way so i couldnt start my car. i had to run the flash all over again while i was getting juice from jumper cables to provide voltage.
Registered User
Joined: Sep 2007
Posts: 257
From: 707 Petaluma, CA
Car Info: 2001 Honda CBR 600 F4i
Splinter,
If you want, since I live in Rohnert Park I can meet up with you tomorrow and let you borrow mine if you just want to go stage 2 for now and worry about the plug later.
If you want, since I live in Rohnert Park I can meet up with you tomorrow and let you borrow mine if you just want to go stage 2 for now and worry about the plug later.
VIP Member
iTrader: (17)
Joined: May 2005
Posts: 22,776
From: Sunnyvale, CA
Car Info: '13 BRZ Limited / '02 WRX
Had to do the same thing when I was unmarrying the V1 AP. Haven't had that issue with the V2, but it may be irrelevant to the AP model.
Thread
Thread Starter
Forum
Replies
Last Post
WRX Coastie
Engine Management
4
Jan 1, 2009 04:24 PM
wrxisthebest
Interior, Exterior & Lighting
0
Mar 16, 2008 04:06 PM
fd3s/wrx
Engine Management
2
Jan 30, 2006 02:37 PM
AndrewSS
Ongoing Projects
3
Mar 23, 2004 01:12 PM
