F.S 2004 WRX full STI swap and built engine
05-14-2013, 02:52 PM
#1
F.S 2004 WRX full STI swap and built engine
It's come time in my life where I need to sell my car. I'm buying a house and need the extra cash to cover the down payment! It's very hard for me to sell something I have but everything into from day one in 2003. The car has a stage 2 EQ tuning engine, full STI swap, (trany, brembos, and full interior) the car has a tremendous amount of work done to it and is an absolute beast. People that have seen the car know it still shins like new and is built to run! As it sits the car is on a low boost map for e85 on DW 1200CC injectors. For full boost and power potential you will need to have some ID 2000CC injectors. The car is located in San Carlos and can been seen and driven for people serious about the car. Asking price is $17,000 but it's also OBO.
[IMG]
[IMG]
05-14-2013, 04:16 PM
#4
Thanks man! I hate to do it but I have a great opportunity to buy a house and I can't pass it up! Ill be back in a year or 2 with a 2014 STI.
And I'll try to get more info up on the car as far as mods and everything go later tonight
And I'll try to get more info up on the car as far as mods and everything go later tonight
05-14-2013, 07:19 PM
#5
Some more engine mods will update with coil over sand other stick to the road mods later.
1. CP 100mm pistons, pins, rings
2. ALC bearings race series ej257 rod, main,thrust #5 position
3. Machine shop work….. Inspect, clean, magnaflux, bore, hone, deck ej257, calance and polish crank, balance rod, line hone mains, clearancing block for new rods.
4. Manley H-Beam connecting rods for ej257
5. EQ Tuning stage 2 shortblock build
6. DeachWerks 1200cc top feed injectors
7. RPS MAX series clutch with street disk
8. APS Hard turbo inlet (black)
9. ATP GT3076 stock location turbo with Crucial Racing port polish & coat turbo
10. GrimmSpeedb up & downpipe gaskets
11. Machine shop 5 angle valve job
12. Cosworth billet timing belt guid
13. Bryan Crower camshafts 2/272’s
14. Bryan Crower single spring titanium retainer kit
15. Black TurboXS FMIC
16. Perring downpipe
17. Tomei header with up pipe
18. NGK Spark plugs
19. Cosworth head gasket
1. CP 100mm pistons, pins, rings
2. ALC bearings race series ej257 rod, main,thrust #5 position
3. Machine shop work….. Inspect, clean, magnaflux, bore, hone, deck ej257, calance and polish crank, balance rod, line hone mains, clearancing block for new rods.
4. Manley H-Beam connecting rods for ej257
5. EQ Tuning stage 2 shortblock build
6. DeachWerks 1200cc top feed injectors
7. RPS MAX series clutch with street disk
8. APS Hard turbo inlet (black)
9. ATP GT3076 stock location turbo with Crucial Racing port polish & coat turbo
10. GrimmSpeedb up & downpipe gaskets
11. Machine shop 5 angle valve job
12. Cosworth billet timing belt guid
13. Bryan Crower camshafts 2/272’s
14. Bryan Crower single spring titanium retainer kit
15. Black TurboXS FMIC
16. Perring downpipe
17. Tomei header with up pipe
18. NGK Spark plugs
19. Cosworth head gasket
05-16-2013, 12:18 AM
#11
It's a asking price.. And I don't feel it's to high.. The car has a lot more then a built engine. It has custom body work and a $7000 paint job. But thanks for the input. The car will see for what it does. I just hope it goes to a good subaru guy!
