Gauge Pic
Thread Starter
Registered User
iTrader: (4)
Joined: Dec 2002
Posts: 2,176
From: Southern California
Car Info: 2016 Z51 C7, 2007 Exige S, 2008 ZX-10R, 2016 Taco
Gauge Pic
Not a good pic, get over it. Left top pillar is Apexi oil pressure, Apexi EGT underneath it. Center pod is Gruppe-S carbon with Defi BF boost, oil temp, and water temp (left to right). In the center right air vent is my PLX M-300 wideband O2. Under the O2 is the Defi control unit. Underneath the control unit are Apexi S-AFC and AVC-R (left to right). Eclipse head unit under them. Silver piece near the S-AFC is the head unit remote.
San
San
Last edited by oldmansan; Mar 7, 2006 at 09:39 PM. Reason: add info
Registered User
iTrader: (26)
Joined: Mar 2004
Posts: 7,140
From: buying a house in hawaii is harder then it looks
Car Info: 2001 Impreza 2.5RS-T 2011 Forester Prem. SUBYS FTW
were did u get your apexi oil press from and is it a 60mm and were did u get the apillar from?
Thread Starter
Registered User
iTrader: (4)
Joined: Dec 2002
Posts: 2,176
From: Southern California
Car Info: 2016 Z51 C7, 2007 Exige S, 2008 ZX-10R, 2016 Taco
I
got the Apexi oil pressure and EGT from Hypersports years ago. They are 60mm (all my round gauges are). They were pricey. I think Vakamon carries them now. The A-pillar is LoTek, which has received mixed reviews. It's a decent pillar, but could fit a bit better. I can show you what I mean. Most won't ever notice any problem.
San
San
Thread Starter
Registered User
iTrader: (4)
Joined: Dec 2002
Posts: 2,176
From: Southern California
Car Info: 2016 Z51 C7, 2007 Exige S, 2008 ZX-10R, 2016 Taco
I'm
not sure what you're asking. I'm guessing you have the same plug on top of the block to accomodate the oil pressure sensor, so the guage should work regardless of your model year.
San
San
Registered User
iTrader: (26)
Joined: Mar 2004
Posts: 7,140
From: buying a house in hawaii is harder then it looks
Car Info: 2001 Impreza 2.5RS-T 2011 Forester Prem. SUBYS FTW
Originally Posted by oldmansan
not sure what you're asking. I'm guessing you have the same plug on top of the block to accomodate the oil pressure sensor, so the guage should work regardless of your model year.
San
San
VIP Member
iTrader: (7)
Joined: May 2003
Posts: 4,990
From: on da compz...readin' yo blogz
Car Info: "the loud one"
just gotta make sure the time circuits are on, the flux capasitor is running fine, set the time destination, and buckle your seat belt before you hit 88mph.....
Thread Starter
Registered User
iTrader: (4)
Joined: Dec 2002
Posts: 2,176
From: Southern California
Car Info: 2016 Z51 C7, 2007 Exige S, 2008 ZX-10R, 2016 Taco
Well,
I tend to purchase things and "make" them fit. I cut into my stock dash almost as soon as I purchased it (7 days). My carbon gauge pod was cut for 52mm holes, but my gauges were 60mm. I decided I'd "enlarge" the holes as I was impatient. What a pain. I should have mounted my Defi control unit in the center armrest console, but I mounted it where the cupholder used to be (serious pain in the @$$). My Apexi rectangular gauges were difficult. It was a lot of custom work.
San
San
