Wheel Offset question, mix matching
Thread Starter
Registered User
iTrader: (3)
Joined: Aug 2005
Posts: 526
From: moved to so cal...
Car Info: Saabaru
Wheel Offset question, mix matching
Hey all, a couple of quick about wheel offsets. First of all, can you measure the wheel offset somehow with a ruler? If not accurately at least approxmiate? Second, is it a bad idea if I mix match wheels with different offset? I was thinking that it might be bad if the the samle axle is running two different ones, but the if the front and the back axels differed it might not be that big of a deal, but I am not sure as I've done really seen that done on AWD cars before. I've been reading about offsets it seems that the wheel bearings like the at least 40 or 42mm, but higher the better, will 42mm work in the wagons? 18x7.5 probably 225/40x18
Last edited by lazybummm; Nov 8, 2005 at 12:36 PM.
It would be hard to measure offsets with a ruler, because the measurement is from the centerline of the wheel to the hub mating surface. Unless, of course, you have a really good eye for the centerline of your wheel.
As for mixing offsets, why do you want to? I don't know if it'd be damaging, but I wouldn't recomend it. It just sounds like a bad idea to me.
As for mixing offsets, why do you want to? I don't know if it'd be damaging, but I wouldn't recomend it. It just sounds like a bad idea to me.
Originally Posted by nKoan
It would be hard to measure offsets with a ruler, because the measurement is from the centerline of the wheel to the hub mating surface. Unless, of course, you have a really good eye for the centerline of your wheel.
As for mixing offsets, why do you want to? I don't know if it'd be damaging, but I wouldn't recomend it. It just sounds like a bad idea to me.
As for mixing offsets, why do you want to? I don't know if it'd be damaging, but I wouldn't recomend it. It just sounds like a bad idea to me.
you wouldnt really need a good eye to figure it out. he said its a 7.5" wheel so 3.75" is center. Just put a dot there and measure to the mounting pad.
Only real reason to run different offset is if you use wider wheels in the back and need clearance. I agree its not a good idea.
Last edited by killaho; Nov 8, 2005 at 10:28 AM.
Thread Starter
Registered User
iTrader: (3)
Joined: Aug 2005
Posts: 526
From: moved to so cal...
Car Info: Saabaru
Originally Posted by nKoan
It would be hard to measure offsets with a ruler, because the measurement is from the centerline of the wheel to the hub mating surface. Unless, of course, you have a really good eye for the centerline of your wheel.
As for mixing offsets, why do you want to? I don't know if it'd be damaging, but I wouldn't recomend it. It just sounds like a bad idea to me.
As for mixing offsets, why do you want to? I don't know if it'd be damaging, but I wouldn't recomend it. It just sounds like a bad idea to me.
I picked up 2 good 18x7.5 wheels from smitty, slvrsubywgn on i-club, unsure about offset(guessing somewhere between 42-48, gonna try and measure), and then I am trying to source 2 more 18's for a cheap price, I've found one that has 42 offset for really cheap, so trying to figure out this mixing and matching scheme. Really I just want to get a set of decent 17/18" inexpensive rims, but not trying to kill my car or my already very thin wallet at the same time...
Registered User
iTrader: (5)
Joined: Dec 2002
Posts: 1,839
From: Folsom, CA
Car Info: 02 WRX/05 Legacy
Originally Posted by killaho
Only real reason to run different offset is if you use wider wheels in the back and need clearance. I agree its not a good idea.
Thread
Thread Starter
Forum
Replies
Last Post
LukeSTi
Wheel & Tire
5
Aug 7, 2005 05:55 PM
GottaREX
New Aftermarket Car Parts For Sale
2
Jun 15, 2004 04:34 PM
