The car came with the Subaru all-weather mats, and I was pretty disappointed in them. I had Subaru mats in my wrx and they were fantastic, these not so much.
So I ordered up the Weathertech liners for front/rear. They are the exact same as the 2017 Impreza. They came in yesterday and I swapped em out, so much better! [img]https://farm5.staticflickr.com/4499/37481835492_11b97a1d59_b.jpg[/img] [img]https://farm5.staticflickr.com/4514/37481833942_0bba2d636a_b.jpg[/img] |
I need to get me some WeatherTech mats, the OEM rubber mats just don't cut it for our winters.
|
[QUOTE=newyorkreload;3655072]I need to get me some WeatherTech mats, the OEM rubber mats just don't cut it for our winters.[/QUOTE]
Im surprised you dont have anything yet! |
Just stop it thomas, you are making me spend money i dont have!
|
[QUOTE=stupidchicken03;3655083]Im surprised you dont have anything yet![/QUOTE]
Didn't have funds to get stuff before 2015 and car was not driven at all last winter. I got floor mats they just lack in ability compared to weathertech [IMG]https://cimg1.ibsrv.net/gimg/www.i-club.com-vbulletin/355x237/80-81qxtwilg4l_sx355__4f317a13c526feec935b071eeb4b31cf1654158c.jpg[/IMG] |
[QUOTE=i<3dirt;3655108]Just stop it thomas, you are making me spend money i dont have![/QUOTE]
But, its just money :D :lol: [QUOTE=newyorkreload;3655110]Didn't have funds to get stuff before 2015 and car was not driven at all last winter. I got floor mats they just lack in ability compared to weathertech [/QUOTE] Gotcha. Yea full floor coverage is always a plus to me. I got the fiance similar stuff when she got the Sorento. Been really happy with them. |
Got the main piece of the next project in the mail on Saturday :)
Ive gotten tired of running individual switches into the car every time I add an another accessory. It adds up to being a lot of wire being ran and individual switches all over the cabin, especially after running out of the blank slots on the drivers side dash. I got this S-Tech system from Team Tech Offroad located in Colorado. Ill be making a bracket to mount the 6 switches below the HVAC controls. I might make another bracket for under the hood to mount the power block as well (unless I can get lucky and it will mount to two existing bolts, but I doubt it lol). So here is the system, i just wired up 3 of the 6 toggle switches to get a feel of it. [img]https://farm5.staticflickr.com/4485/36924819073_6898fc0e6b_b.jpg[/img] Here are the switches I got. Dual LED so they will be partially illuminated while off and fully when switched on. All of them are red colored to match the Speedo/Tach. I got 4 of them labeled for the future plans, and 2 blanks as im not sure what i would want to fill them with yet ;) [img]https://farm5.staticflickr.com/4488/37545976826_668345e0ab_b.jpg[/img] |
Also had to pull the cars up next to each other for obvious reasons lol
[img]https://farm5.staticflickr.com/4495/37595298261_1ff58c5333_b.jpg[/img] [img]https://farm5.staticflickr.com/4466/37595297821_29a4d9f8f2_b.jpg[/img] |
That's kinda neat.
You get 6 switches that feed into one fat cable that goes into a box with fuses and relays? |
[QUOTE=JourdanWithaU;3655218]That's kinda neat.
You get 6 switches that feed into one fat cable that goes into a box with fuses and relays?[/QUOTE] Yup. So now to power an accessory, I only have to run 1 wire for the power (to the distribution block), the other end just needs to be grounded wherever that accessory is. I originally wanted an S-Pod that is basically the same thing, but instead of all the single cables (as 1 big one) going into the cab, they made it all work with an ethernet cable. But that system is over double what I paid for this... so... |
Ethernet cable is clever.
Could probably do something similar with 9 conductor speed wire. |
I just hate wiring in general. So this was simple enough for me :laugh:
|
Tell me more about this "compressor" you're puttign in.
|
I like the switch box that's pretty cool!
|
^Thank ya
[QUOTE=newyorkreload;3655222]Tell me more about this "compressor" you're puttign in.[/QUOTE] hehe. Ive been thinking about putting in an ARB single tank compressor where the spare tire should go (I took it out since its pointless). They are rated to fill a 35" tire in about 2 minutes :) The dual tank ones are baller and I think you can run air tools off of them. But its more than I want to spend, and space might be too tight for it. |
All times are GMT -7. The time now is 11:08 AM. |
© 2024 MH Sub I, LLC dba Internet Brands