FS: JIC Magic Ti Exhaust w/ Cobb catted dp
Registered User
iTrader: (4)
Joined: Mar 2005
Posts: 89
From: South Bay Area, CA
Car Info: 05 AW WRX STi
Got any actual pictures of the exhaust? Is this an older version where it has a taper to meet the stock (and Cobb) downpipe or is it a full 3" with a flat flange?
Thread Starter
Registered User
iTrader: (12)
Joined: Dec 2002
Posts: 694
From: El Cerrito, CA
Car Info: 2004 WRX
From what I can recall from the time I installed the exhaust, it has a taper to the downpipe. I dont think it has a flat flange.
In terms of actual picture, the exhaust is still on the car since that's the only exhaust I have right now. But I will be able to post up some pictures of it on the car, hopefully by tonight.
Please PM me your email too so I can send you the pictures if I can't figure out how to post it online. =D
-Mark C.
In terms of actual picture, the exhaust is still on the car since that's the only exhaust I have right now. But I will be able to post up some pictures of it on the car, hopefully by tonight.
Please PM me your email too so I can send you the pictures if I can't figure out how to post it online. =D
-Mark C.
Registered User
iTrader: (15)
Joined: May 2005
Posts: 1,391
From: www.fatlace.com www.gripunit.com
Car Info: www.hellaflush.com
Are you replacing it with something else Mark? Or going back to stock o.O
tell me you are going with a 4'' downpipe with a 3'' straight pipe, lol
tell me you are going with a 4'' downpipe with a 3'' straight pipe, lol
Thread Starter
Registered User
iTrader: (12)
Joined: Dec 2002
Posts: 694
From: El Cerrito, CA
Car Info: 2004 WRX
lol. nah, that will be even louder than my exhaust right now. I want to go with something quieter. My gf has been complaining.
I will try to post up pictures tomorrow morning.
-Mark C.
I will try to post up pictures tomorrow morning.
-Mark C.
Thread Starter
Registered User
iTrader: (12)
Joined: Dec 2002
Posts: 694
From: El Cerrito, CA
Car Info: 2004 WRX
Sorry for the bad night pictures, I took these at 4am in the morning. =(
The day picture is from around 3 months ago. Same car, same setup. It gives you a better look of how it looks like in the day time.
-Mark C.
The day picture is from around 3 months ago. Same car, same setup. It gives you a better look of how it looks like in the day time.
-Mark C.
Registered User
iTrader: (4)
Joined: Mar 2005
Posts: 89
From: South Bay Area, CA
Car Info: 05 AW WRX STi
Aww the black coating makes me sad... can't see the Ti bling! =)
Is there any way to remove it? From the pics it also seems like the non-resonated version. Sorry for all of the questions and comments, I'm looking for an exhaust for my friend so I needed all of the details.
Is there any way to remove it? From the pics it also seems like the non-resonated version. Sorry for all of the questions and comments, I'm looking for an exhaust for my friend so I needed all of the details.
Thread Starter
Registered User
iTrader: (12)
Joined: Dec 2002
Posts: 694
From: El Cerrito, CA
Car Info: 2004 WRX
No problem eXstasy, ask as many questions as you want, and I will try to answer them as well as I can.
From my knowledge, the black finish is here to stay. =( sorry about that, I dont think I can remove it. I am not sure if you can polish it back to the original state though.
It does have a resonator, from my original post, I said it was the cat that was dented. But it is actually the resonator. I have pictures of it below.
-Mark C.
From my knowledge, the black finish is here to stay. =( sorry about that, I dont think I can remove it. I am not sure if you can polish it back to the original state though.
It does have a resonator, from my original post, I said it was the cat that was dented. But it is actually the resonator. I have pictures of it below.
-Mark C.
Last edited by chakming888; May 11, 2007 at 11:18 AM.
Registered User
iTrader: (4)
Joined: Mar 2005
Posts: 89
From: South Bay Area, CA
Car Info: 05 AW WRX STi
Oh, you're right, the flange is full sized however I meant to ask about the piping, sorry.
The older versions of the JIC tapered to 2.5" to mate up with the stock downpipe. Luckily, the Cobb DP also tapers in order to fit stock catbacks. So the combo you have here is perfect!
The older versions of the JIC tapered to 2.5" to mate up with the stock downpipe. Luckily, the Cobb DP also tapers in order to fit stock catbacks. So the combo you have here is perfect!
