FS: Blouch 1.5 XTR, Perrin 3" inlet, Perrin Big MAF
Thread Starter
Registered User
Joined: Feb 2010
Posts: 106
From: Redding, Ca.
Car Info: 2007 Subaru Wrx Sti
SOLD!SOLD!SOLD!
Thanks everyone!
I have a Blouch 1.5 XTR with 8 CM hotside and a 3" inlet. The turbo is as close to new as your going to find! I ran it on my car for less than 2,000 miles and decided it was the wrong turbo for my setup and I switched to a 18G. The turbo has zero shaft play and looks like it just came out of the box, because it did! I bought it directly from Blouch and paid $1700. Comes with stainless oil line.
Equilibrium tuning pulled the turbo off on thursday. I have it boxed up and ready to ship. Shipping should be around $20, because of the weight of it.
Here are the specs on Blouch's website.
Specs
Garrett Ball bearing CHRA
56.5mm Turbine Wheel
71mm XT Compressor wheel
49lbs per min
8cm exhaust housing
$1300 OBO. Available for shipping or local pickup in Redding, Ca. I will also be in the bay area in May and could bring it down with me.
I also have a Perrin 3" inlet. The inlet was bought and installed when I installed the turbo. It is in perfect shape as well. I had to use some of the fittings for the new inlet. What you see pictured is what you get. So you may have to find some fittings which is rather simple.
$150 OBO. Available for shipping or local pickup.
Perrin Big MAF intake in crinkle red. In good shape. Has a few scratches but they are underneath the intake when mounted. I bought this on Nasioc and never even installed it.
$115 OBO. Available for shipping or local pickup.
Thanks everyone!
I have a Blouch 1.5 XTR with 8 CM hotside and a 3" inlet. The turbo is as close to new as your going to find! I ran it on my car for less than 2,000 miles and decided it was the wrong turbo for my setup and I switched to a 18G. The turbo has zero shaft play and looks like it just came out of the box, because it did! I bought it directly from Blouch and paid $1700. Comes with stainless oil line.
Equilibrium tuning pulled the turbo off on thursday. I have it boxed up and ready to ship. Shipping should be around $20, because of the weight of it.
Here are the specs on Blouch's website.
Specs
Garrett Ball bearing CHRA
56.5mm Turbine Wheel
71mm XT Compressor wheel
49lbs per min
8cm exhaust housing
$1300 OBO. Available for shipping or local pickup in Redding, Ca. I will also be in the bay area in May and could bring it down with me.
I also have a Perrin 3" inlet. The inlet was bought and installed when I installed the turbo. It is in perfect shape as well. I had to use some of the fittings for the new inlet. What you see pictured is what you get. So you may have to find some fittings which is rather simple.
$150 OBO. Available for shipping or local pickup.
Perrin Big MAF intake in crinkle red. In good shape. Has a few scratches but they are underneath the intake when mounted. I bought this on Nasioc and never even installed it.
$115 OBO. Available for shipping or local pickup.
Last edited by dahgoose; May 6, 2013 at 08:36 AM.
Registered User
iTrader: (12)
Joined: Sep 2011
Posts: 2,057
From: San Mateo, CA
Car Info: 2015 FXT Stage II
Thread
Thread Starter
Forum
Replies
Last Post
WrX89
Hawaii Classifieds
0
Nov 12, 2013 03:24 AM
BOHICA
Used Aftermarket Car Parts For Sale
6
Apr 29, 2013 11:22 AM
jung187
Used Aftermarket Car Parts For Sale
1
Jan 10, 2013 07:17 AM
pj21086
New Aftermarket Car Parts For Sale
11
Jan 11, 2006 11:56 PM
