Anyone Paintball?
Thread Starter
Registered User
Joined: Sep 2004
Posts: 103
From: Racine, WI
Car Info: 04 WRX WR Blue
Anyone Paintball?
I have two markers for sale hate to part with them but I can only play with one at a time.
One is a 2002 WGP Autococker (semi-auto) Full front tweaked pneumatics, shoots straight and fast, have about 30 cases through it, it is pre drilled and taped for the Eblade eye, Milled "window" so you or other people can view the bolt action.
Mods are:
2002 Milled Semi Gloss black body (450 stock from WGP)
Sonic Black Sonic Regulator (55)
STO 3 Way (35)
Palmers Ram (45)
Shocktech Clear Pneumatic hoses (3.50)
Shocktech 3:16 low pressure high flow valve (65)
Chrome front block and bolt (65)
Chrome BlackMagic trigger frame (90)
14" Chrome Custom Products Barrel (45)
also selling with it stock pneumatics, stock barrel, and triggerframe.
asking $500 obo build cost 850 including marker
The second one is a AirGun Designs 68 Automag also fully tweaked and owned by an Airsmith (ME) this also has about 30 cases through it due to extensive testing and tweaking not to mention the fun factor and weighs less than a td06. Can only use COMPRESSED AIR due to the retro valve. This valve uses the pressure in the tank to 'bounce' the trigger back. but since there is an electronic trigger you would not notice. The retro valve can shoot about 25 palls a second but limited to the Hyperframes 13 pbs. and with the lvl 10 you could efectively stick your fingure or toungue in the chamber and pull the trigger with out taking it off... I actually tried it with my finger and it is still there.
*the only thing wrong is that in my last game the pin that holds the barrel in place jammed and broke while playing* I will in fact replace it for a serious buyer at no charge.
68 Automag Black power feed body (450)
Lvl 10 anti chop bolt with extra shims and fittings (75)
Center Flag Hyperframe (350)
AGD ReTro Valve ($250)
and I have a few barrels to choose from 10" PMi, 8" Dye stainless
No stock parts other than bolt and springs
asking $650obo build cost well over $900 Including marker
I am willing to sell one with a full setup (compressed air tank, hopper, hose + fittings) for an aditional $350. The Air Tank is a PMI 68 cubic inch 4500 PSI and the hopper is a 9volt View loader revolution (automaticaly agitates paint to feed in feed tube)
Have a ton of pictures
For details or question
E-Mail BluSube04@Gmail.Com
AIM MitsurugiSeito
One is a 2002 WGP Autococker (semi-auto) Full front tweaked pneumatics, shoots straight and fast, have about 30 cases through it, it is pre drilled and taped for the Eblade eye, Milled "window" so you or other people can view the bolt action.
Mods are:
2002 Milled Semi Gloss black body (450 stock from WGP)
Sonic Black Sonic Regulator (55)
STO 3 Way (35)
Palmers Ram (45)
Shocktech Clear Pneumatic hoses (3.50)
Shocktech 3:16 low pressure high flow valve (65)
Chrome front block and bolt (65)
Chrome BlackMagic trigger frame (90)
14" Chrome Custom Products Barrel (45)
also selling with it stock pneumatics, stock barrel, and triggerframe.
asking $500 obo build cost 850 including marker
The second one is a AirGun Designs 68 Automag also fully tweaked and owned by an Airsmith (ME) this also has about 30 cases through it due to extensive testing and tweaking not to mention the fun factor and weighs less than a td06. Can only use COMPRESSED AIR due to the retro valve. This valve uses the pressure in the tank to 'bounce' the trigger back. but since there is an electronic trigger you would not notice. The retro valve can shoot about 25 palls a second but limited to the Hyperframes 13 pbs. and with the lvl 10 you could efectively stick your fingure or toungue in the chamber and pull the trigger with out taking it off... I actually tried it with my finger and it is still there.
*the only thing wrong is that in my last game the pin that holds the barrel in place jammed and broke while playing* I will in fact replace it for a serious buyer at no charge.
68 Automag Black power feed body (450)
Lvl 10 anti chop bolt with extra shims and fittings (75)
Center Flag Hyperframe (350)
AGD ReTro Valve ($250)
and I have a few barrels to choose from 10" PMi, 8" Dye stainless
No stock parts other than bolt and springs
asking $650obo build cost well over $900 Including marker
I am willing to sell one with a full setup (compressed air tank, hopper, hose + fittings) for an aditional $350. The Air Tank is a PMI 68 cubic inch 4500 PSI and the hopper is a 9volt View loader revolution (automaticaly agitates paint to feed in feed tube)
Have a ton of pictures
For details or question
E-Mail BluSube04@Gmail.Com
AIM MitsurugiSeito
Thread
Thread Starter
Forum
Replies
Last Post