UTEC remote switch install(large pics)
01-01-2003, 10:07 PM
#1
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
UTEC remote switch install(large pics)
Probably the most simplest installation; took me all day, though.
The biggest part was trying to carefully drill and dremel the 'blank' that is next to the cruise control button.
The biggest part was trying to carefully drill and dremel the 'blank' that is next to the cruise control button.
01-01-2003, 10:08 PM
#2
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
The zero is the number of the map. It's got 2 little clickers so you can cycle through pre-programmed maps.
The key is to set it to 'valet' mode.
The key is to set it to 'valet' mode.
Last edited by gpatmac; 01-01-2003 at 10:10 PM.
01-01-2003, 10:12 PM
#4
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
...yes I did. Thanks a bunch.
Damn, my friggin TAB key is switching between windows and not fields!!!!
It doesn't look as bad as this. No really.
Sean, you can't look under my dash. I'm afraid of what you might find.
Damn, my friggin TAB key is switching between windows and not fields!!!!
It doesn't look as bad as this. No really.
Sean, you can't look under my dash. I'm afraid of what you might find.
01-01-2003, 10:16 PM
#6
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
All Pau.
Anyhow, originally the UTEC came with a blank, white male connector to fit into the female on the unit itself. It took me a while to figure out that I had it. I was trying to poke bare wires into the female part. What a dunce.
Oh, yeah. And I finally installed the TurboXS 'closed loop boost control' firmware into my UTEC. Hopefully I'll have it figured out by the time I get back from Lousy Anna.
Works like a charm....for now.
Dan and Sean want my light hat.
Anyhow, originally the UTEC came with a blank, white male connector to fit into the female on the unit itself. It took me a while to figure out that I had it. I was trying to poke bare wires into the female part. What a dunce.
Oh, yeah. And I finally installed the TurboXS 'closed loop boost control' firmware into my UTEC. Hopefully I'll have it figured out by the time I get back from Lousy Anna.
Works like a charm....for now.
Dan and Sean want my light hat.
Last edited by gpatmac; 01-01-2003 at 10:19 PM.
01-01-2003, 11:03 PM
#10
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
It's actually supposed to send a little jolt to the squirrel up under my hood.
I call him Gnawss because of the way he eats at the twigs and berries.
I call him Gnawss because of the way he eats at the twigs and berries.
01-01-2003, 11:22 PM
#11
Angry Dan
iTrader: (9)
Join Date: Nov 2002
Location: www.turboculture.com
Posts: 7,183
Car Info: 05 Evo VIII
Originally posted by gpatmac
It's actually supposed to send a little jolt to the squirrel up under my hood.
I call him Gnawss because of the way he eats at the twigs and berries.
It's actually supposed to send a little jolt to the squirrel up under my hood.
I call him Gnawss because of the way he eats at the twigs and berries.
01-01-2003, 11:36 PM
#12
Where is my beer?
iTrader: (1)
Join Date: Nov 2002
Location: San Diego
Posts: 4,677
Car Info: NSX, G35
Pat, you are too much! LOL! 
I hope you got everything hooked up ok. I didn't get a phone call from you, ..... so that's a good thing, ... right? (yes, b/c my a$$ wasn't gettting out of bed anyway!!
I didn't get home until the sun was up!)
you know, you may want to order some new 'blanks' from the dealership, ... if you want, I'll demel those things to fit in there and make it look perfect
I hope you got everything hooked up ok. I didn't get a phone call from you, ..... so that's a good thing, ... right? (yes, b/c my a$$ wasn't gettting out of bed anyway!!
I didn't get home until the sun was up!)you know, you may want to order some new 'blanks' from the dealership, ... if you want, I'll demel those things to fit in there and make it look perfect
Thread
Thread Starter
Forum
Replies
Last Post
IMPREZIN
Engine Management
0
08-11-2006 10:58 AM