Funks

iTrader: (3)

Here's one in the San Jose

R C Refinishing - Refinishing Services

and here's one in Belmont

Accessories Plus - Auto Parts & Supplies

I'm getting my HKS Equal Length Header sometime next week and I want to get it ceramic coated. Both these places use Cerakote.

norcalbro

iTrader: (11)

I had my ar15 cerakoted at RC. They know what they are doing. I have been dealing with them for years. Highly recommended

PROcede

iTrader: (12)

I've had a couple pieces done at Accessories plus in belmont. They actually do a lot of Subaru headers, downpipes, ect. Definitely check them out.

SkizzDawg

iTrader: (7)

*COUGH* swaintech *COUGH*

you get what you pay for.

El Wray

iTrader: (1)

whats the price typically run for a header or dp?

wwrx

iTrader: (5)

I talked to Accessory Plus guy a few years ago. He was very helpful. He told me that their coating is either 1 or 3 mil thinkness. At the same time Swaintech coating is 15 mil! I chose Swaintech for EL Headers. It costed me half the price of the headers

Now, for a DP I'd probably go to Accessory Plus and then just wrap it. Or just wrap it without any coating (that's what I did).

wwrx

iTrader: (5)

For my headers price (excluding the shipping cost TO Swaintech) was either $320 or $350 total. That's for Tomei Headers plus uppipe. Plus shipping from Swaintech that wasn't cheap. Price is from Feb-March 2012.

I think Accessory Plus quoted me ~$200-$250 for the same work.

stg2lgcy00

iTrader: (23)

Went to Accessories Plus a few years ago to coat my Borla, other than typical road grime on the header the coating is still holding strong.

Funks

iTrader: (3)

Thanks for the reply, sounds like these two local shops are capable of getting the job done (both have coated Subaru Headers and Downpipes). I sent some pics to RC finishing and they'll give me a quote, Accessories Plus on the other hand requires that I swing by in person and they need to measure it to give me a quote.

Will post up the quotes I get..

As for swaintech, dont' really want to go that route -the HKS headers actually have an aluminum heatshield that it comes with, I don't want to wrap the header.

Lowend

iTrader: (5)

I've used Accessories Plus for literally hundreds of pieces, they are always top notch

WRXncrew

iTrader: (6)

+1, but not hundreds of pieces. 1 downpipe, 2 headers, 2 uppipes, and a short EWG pipe. Reasonable and quick turnaround, talk to Steve he's a good guy.

Funks

iTrader: (3)

Dropped off the header at Accessories Plus (Belmont) - Steve, charging me 235$ to get it coated.

Not sure how much R.C. Refinishing charges (they never got back to the e-mail I sent with pictures which they told me to do when when I called them).

There's a couple of shops in Walnut Creek/Concord that does Cerakote high-temp coatings (certified applicators) too but not sure what the quality of their work is..

E-Tech Powdercoating
925-934-1872
2141 North Broadway, Walnut Creek

Industrial Solutions
925-682-4828
1090 Shary Circle, Suite D
Concord

Rescuer

iTrader: (9)

lol

https://www.i-club.com/forums/bay-ar...-creek-246937/

Funks

iTrader: (3)

Accessories Plus is legit - I walked in there today and saw a "WALL" of headers / turbo manifolds / turbo hot side being sandblasted, then coated. Those guys don't play around - lol. They've definitely been doing this sorta thing a while.

Need more reviews of the other local shops for their ceramic coating work, not powdercoating. I would like to know what preparation process they use so that we know we are getting quality..

Do they

1) Sandblast / mediablast the parts?
2) Bake the parts in an oven to make sure it gets rid of the oils in the pipes (brand new tubes have have all kinds of contaminants in it from the forming / bending / extrusion process)?
3) Applied Ceramic coating using a spray gun then bake it after to make sure it cures correctly?

Inquiring minds wanna know - this **** is expensive.

norcalbro

iTrader: (11)

I can tell you from experience that RC does media blast to prep. Spray then bake taking proper steps. They do great work. They are just a little tough to get a hold of...